Jump to content

gaggia

Član
 Pogledaj profil  Pogledaj aktivnost profila

  • Broj sadržaja

    2668

  • Na DiyAudio.rs od

  • Poslednja poseta

  • Broj dana (pobeda)

    2

 Content Type 

Postovi objavljeno od gaggia

    Linux

    in IT

    Napisano

    Uh Žiko namuci me, pet minuta da razrešim zagonetku "nomodeset", znači nedostaju mi neki kernel parametri. Ok, proučim malo i to.Thanks

     

    probaaaj taj ubuntu - ne bih ti predlagao da nisam ubedjen da je odlican - progooglaj malo o tematici ubuntu+tvoja graf karta (uzgred- koja je u pitanju?)

    Linux

    in IT

    Napisano

    Razmišljao sam i o tome, na poseban hd da instaliram, videću sutra to da odradim. pa javljam utiske. Hvala  :phil_04:

     

    ne budes li - vise ne razgovaram s tobom :D 13.10 - 32 ili 64bit-na (obrati paznjicu)

    Beyma koaksijalac - tannoy alternativa ili nešto sasvim drugačije

    in Zvučnici

    Napisano

     

    Pokusavao sam da ugodim BR (jako) nisko, ali nisam dobio basa...
    Slusao sam jedared MLTL, nije imalo basa: 12" k'o 12cm... 
     
    Tako daaa... izvin'te sto Vas ne razumem...  :salute:V  

     

     

    Kazi bre lepo: "slus`o sam gagijeve EV u MLTL i nije se culo ni za precvaloga duda (a u srcu svome sapuci - "nije istina, nije istina,nije...")  :D A tek da znas sta mi sada miluje usne mi skoljkeeee...uffffffff..ne bi ti bilo svejedno - ne bih da te sikiram :wave:

    Linux

    in IT

    Napisano

    udriiiiiiiiiiiiiiiii!!!!! Ajde ti lepo skini Ubuntu Studio, narezi distribuciju ili speci na flash Unetbootin-om. Izaberi Try without installing i vidi sta sve moze :) Da znas - tesko se vraca covek na win.. Iii da - mogao bi da za probu dofatis neki npr 80gb disk pa da na njega, odvojeno od windowsa, instaliras lindzu.

    Preporuka za pojačalo u A klasi

    in Solid State

    Napisano

    dvv 

     

    Sta se ti petljas sa nama kada smo mi vecina sa DIY Audio RS po Tvom misljenju gomila neznalica ? , a Zen je samo obican serviser pokvarenih audio uredjaja ? , 

    Odnosno kada ces i da li ces se Svima Nama Javno Izviniti za ono tvoje ne tako davno pluvljanje po nama na Big DIY Audio sajtu ? 

     

    ama on je to dobronamerno...

    DIY Synergy horn

    in Zvučnici

    Napisano

    JLH, PP, april 2011`

    If you don’t have access to measurement equipment then you should forget about building a Unity horn. It is too complicated of a project and that is why so few people build one. They are very difficult to build. If they were easy to build then everyone would be building them. They are also expensive to build. I already have $1200 in parts invested into my Synergy project and expect it to cost almost $3000 in the end.

    While I’ll be trying the Misco mids, I do not know if they will work in the end. I’m not even sure if I will keep the BMS 4552ND. I would advise you to wait for me to start my construction thread before you do anything. I’m still working on the preliminary details so will not be starting the construction thread for at least 3 months.

    Paul Spancer, PP

     

    S3 update
    You may have noticed that I've been quiet on the blog about S3 progress. If you thought it was because not much has been happening then this will be a surprise. I now have a small team that has been working hard on creating a statement speaker that is unlike anything you've seen before. The bar has been lifted. The S3 prototype measures very well and performs well subjectively. However, one aspect that I consider to be a compromise is the transition from a circular aperture to a rectangular mouth. The Yorkville Unity uses an axi-symmetric horn but once all aspects of performance are considered, an elliptical form is the ideal shape for a Unity/Synergy horn.
     
    A further challenge with the original plan and design is that there is considerable difficulty in assembly. After assembling three prototypes, I have learnt that some aspects are inherently challenging and don't get easier. It's quite a bit more difficult than most people expect. No doubt there are some within the group that consider this a non-issue but we need to cater to the broad range of skill levels.
     
    As such, I now present an option that the team has been working on behind the scenes. I was concerned initially that the cost of this option would mean a price increase but, after some investigation, we now believe there's a good chance we can deliver without a cost blow-out. We are about to submit this design and obtain quotes.
     
    The following images show the updated S3 design.
     
    Postavljena slika
     
    S3 is now elliptical with fibreglass construction.
     
    Postavljena slika
     
    (CD not shown)
     
    This design is being offered exclusively to those who have paid the deposit for the mids. This will only be offered once and it's limited to those who were in the initial pre-order, or who have paid deposits. This is a not for profit venture. We anticipate that it will run at a loss. However, this project has always been about creating something that has never been offered before, something unique.
     
    If S3 is ever made available in the future, the price would be substantially increased. I'm now working in the audio industry and it would undermine my business to offer a high end statement speaker like this at cost price. I believe that S3 represents a very serious attempt at creating the ultimate horn speaker for the music lover.
     
    Did you have your heart set on building a flat pack? I realise that for some, the desire to build your own is a big issue. I understand that urge very well. I will reiterate that an S3 flat pack would still represent a considerable challenge to build. It was a concern that some may struggle with certain details that aren't obvious until you actually build it. I have built 3 pairs and I can tell you that it's much harder than it looks.
     
    The elliptical design is superior in performance, requires very little time to get up and running and there is still plenty of scope for DIY effort with the stand, mounting and bass module arrangement. It also offers a surface that is suited for spray painting, where ply or MDF are problematic. The horn will be supplied finished in black, but those wanting different colours could spray the colour of their choice.
     
    We are letting you know ahead of getting quotes so that there is some warning before we ask for payment. We require the next payment to cover manufacture before proceeding. If you anticipate financial difficulties, please let us know. We have a waiting list so if you are unable to proceed we will offer you place to another. Future availability is not promised and a significant price rise is certain.
×
×
  • Kreiraj novo...