Eci

I dolaze stege..And here come the clamps..

Posle treba postaviti deo GPošto je jedna strana furnirana, deo G se na deo T postavlja tiplamaNow the part G should be placedBecause the upper side of G is veneered, Part G ( the top of the box ) is set on part T with dowels.

Pogled od napred Zadnja strana je stavljena ( nije pričvršćena ), čisto da se vidi kako se formira kutija Tu je i naziv projekta, probani su razni fontovi i veličine papira, kao i gde treba papir postaviti View from the front The rear side ( part E ) is added ( it is not attached ), just to see how the box looks like Here is also the name of the project, various letter fonts were tested and various paper sizes, also where to set the paper

Pogled od nazadRear View

Postavljanje stranice AUpotreba veoma jakih stega za vertikalno stezanje je neophodnoSetting up the A sideUsage of very strong clamps for vertical clamping is necessary

Pripremljen deo BPrepared part B

Ubačene su tipleThe dowels are inserted

Stranica A ( obe strane isfurnirane ), izbušene su rupe za tiple za spajanje sa delom BThe A part (both sides veneered), holes are drilled for the dowels, for connection with part B

Isto procedura, levoProbane su i razne ukrasne lajsne na spoju furniranih površinaThe same procedure, on the left side.Various decorative moldings were tested on the junction of veneered surfaces.

Furniranje dela K, desnoMera je uzeta papirom, pa se kroji furnirVeneering the part K, on the right side.The measure for veneer was taken earlier with a paper.

Pa gornjeVeneering the upper curve.

Furniranje donje krivine. Mera uzeta ranije papirom.Veneering the lower curve. The measure for veneer was taken earlier with a paper.

Unutrašnjost kutije, pogled na S2 i S1Zabušene rupe i zavrnute matice sa spoljnim navojem ( unutrašnji navoj je 6mm ). Matice gore i dole prodiru kroz S1 u MDF, a levo i desno u deo K. HPD385 se postavlja iznutra.The box from inside, view to parts S2 and S1 .The holes are predrilled and the “Insert Nuts for wood Type D M6x13mm “are tightened. Nuts up and down across the S1 penetrate into the MDF. Nuts left and right into the parts K. HPD385 is placed from inside the box.

Ovaj momenat nije na crtežima. Na stranicu C iznad dela B izbušiti otvor prečnika 100mm. Ovim se uključuje u kompresioni deo kutije i zapremina koja je ograničena sa C, B, A i T This move is not on the drawings. On the side C, above the part B, drill a hole of 100mm diameter. With this, the volume what is limited with parts C, B​​, A and T is added to the compression part of the box.

Popune se neravnine i izravna se površina Fill with putty the uneven surfaces and flatten them

Priprema prednje horne za furniranje Preparation of the front horn for veneering

Okrene se kutija, stavlja se šper 4mm, priprema i realizacija je identična kao u prethodnom slučaju Then the box was turned around, and the 4mm plywood was pasted. Preparation and realization is the same as above

Krajnji rezultat The final result

Način fiksiranja The fixing method

Stavljen šper, donji deo je fiksiran. Postepeno se krivi i kucaju se ekserčići. The lower part of the plywood was fixed. After that the plywood was gradually bended and set with glue and small nails.

Nanošenje lepka na donju krivinu. šper 4mm je iskrojen pomoću papirnog modela. Nosači naležu 5mm na otvor od H, MDF je 19mm. Kada se sabere to je 28mm što je i debljina H. Application of glue on the lower curve. The plywood was cut out, using the previously made paper model. Carriers are laying 5mm on the opening of H, the MDF is 19mm thick, the plywood is 4mm thick. All thicknesses added up making 28mm, what is also the thickness of H.

Okrene se kutija, uzme se mera i za gornju krivinu Then the box was turned around, and the measure was taken also for the upper curve.

Mera se uzima papiromDonja krivina The measure was taken with paper.The lower curve

Krivine se dobro obrade šmirglom, priprema za sledeći postupak : stavljanje šper ploče debljine 4mm na MDF Curves have to be well processed with sandpaper, and the next process could start: putting on the 4mm thick beech plywood on the prepared MDF surface

Formirane prednje horne Front horns are completed